 Wolfe Race Craft 6 point bolt in '93-02 & Carbon Fibre hood |
|
|||||||||
  |
 Apr 26 2011, 04:23 PM
Post
#1
|
|
|
Member  Group: Advanced Members Posts: 59 Joined: 12-May 10 Member No.: 12,601  |
Rollbar is sold
I also have a protoype carbon fibre hood. It came installed and painted on the car, and attaches with 4 hood pins (included). It is not show car quality, there are a couple of blisters on the surface, and a couple of the reinforcing ribs have been trimmed for underhood clearence. $200 + shipping http://i1137.photobucket.com/albums/n506/9...e1/P1000673.jpg http://i1137.photobucket.com/albums/n506/9...e1/P1000668.jpg http://i1137.photobucket.com/albums/n506/9...e1/P1000666.jpg http://i1137.photobucket.com/albums/n506/9...e1/P1000665.jpg This post has been edited by 96Mike: Jun 1 2011, 11:55 PM |
 |
 
|
|
Apr 27 2011, 05:28 AM
Post
#2
|
|
|
Member Group: Advanced Members Posts: 207 Joined: 26-September 04 From: SoCal Baby! Member No.: 472 |
Any photos of the Roll Bar?
This post has been edited by SVTHuh: Apr 27 2011, 05:29 AM |
|
|
|
|
Apr 27 2011, 05:55 AM
Post
#3
|
|
|
Member Group: Advanced Members Posts: 59 Joined: 12-May 10 Member No.: 12,601 |
Here is the pic at Wolfe, http://www.wolferacecraft.com/detail.aspx?ID=246
I'll mock it up on weds and take a pic of it, I just have to find a good hosting site. For those considering it, I'll pay any shipping over the $175 that Wolfe charges, that is to the continental USA |
|
|
|
|
Apr 27 2011, 01:51 PM
Post
#4
|
|
|
Member Group: Advanced Members Posts: 91 Joined: 19-December 07 From: Ontario, Canada Member No.: 2,049 |
Any pics of the hood and it's defects? what years of f-body does it fit?
|
|
|
|
|
Apr 27 2011, 03:20 PM
Post
#5
|
|
|
Member Group: Advanced Members Posts: 59 Joined: 12-May 10 Member No.: 12,601 |
QUOTE (93zder @ Apr 27 2011, 08:51 AM)  Any pics of the hood and it's defects? what years of f-body does it fit? Yes I will put pics them up this eve, it's a '98-'02 Camaro (non-SS style) |
|
|
|
|
Apr 28 2011, 03:10 AM
Post
#6
|
|
|
Member Group: Advanced Members Posts: 59 Joined: 12-May 10 Member No.: 12,601 |
OK I set up a photobucket account, and put up rollbar and hood pics. I was describing the hood by memory in the earlier post, turns out it wasn't blistered. What I was referring to was the reinforcing ribs on the underside seemed to trap gas or similar during it's manufacturer, and it caused the hood to bulge a little above the ribs. The hood is painted hugger orange and you can see the cloth pattern underneath the paint. I also weighed the hood, and i came in at a hefty 8 lbs
http://s1137.photobucket.com/albums/n506/96Mike1/Low%20res/ This post has been edited by 96Mike: Apr 28 2011, 05:51 AM |
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 17th September 2024 - 12:54 AM |