IPB

Welcome Guest ( Log In | Register )

Blaine Fabrication.comUMI PerformanceUnbalanced EngineeringSolo PerformanceHotpart.com
 
Reply to this topicStart new topic
> Koni struts/shocks, front suspension parts
roostmeyer
post Apr 25 2018, 04:16 PM
Post #1


Advanced Member
**

Group: Advanced Members
Posts: 559
Joined: 20-January 09
From: Wichita, KS
Member No.: 3,727



I'm just now unpacking the garage after moving and I'd rather sell this stuff than tossing it up into the attic forever. As much as I'd like to buy another thirdgen for a daily driver or do a lemons build I don't see me using these parts anytime soon.

$250+shipping SOLD
Front koni struts I was told they were valved for super stock back in the day and are degassed for a lower ride height. I had them close to maxed out with ~1300lb/in front springs, but they were working fine when removed. The rears are a set of thunderbird (solid axle) double tube koni's but match up about perfectly in terms of length. The adjusters are stuck at full soft I think. I may try hitting them with an impact and see if they loosen up. I never ran the rears, but kept them around for spares. If I can find all the parts I'll throw in my old spherical strut mounts too.

$40+shipping SOLD
-I have trackbird's old steering gear parts that were close to new. They maybe have another 60 autox runs on them. Center link, idler arm, inner/outer tie rods with hex adjusters. I'll double check, but last time I checked the idler it was still tight.

$20+shipping
12:1 box rebuilt from o'reillys and adjusted on the bench before installation

$40+shipping SOLD
Spindles have the dust cover holes drill and tapped, stock hubs with the rotors cut off, and I'll turn what's left of the rotors down to hubs.

$10+shipping
Performance Friction Front brake pads for 98+ f-body.

Free+shipping
GONE-Front LCA's with poly bushings installed and +1/2 LBJ's. LBJ's are toast with a lot of vertical movement.
GONE-Stock WS6 springs cut down alot, probably not useful for anyone that hasn't done a ton of weight loss
GONE-1100lb springs cut down to approximately 1300lb/in same as above, probably not useful for someone that hasn't done a ton of weight loss.
GONE-My old steering gear parts that I removed to put in trackbirds. Idler was a little loose, but everything else was fine.
-3.27 9 bolt ring and pinion
-Original 12:1 steering box from my car. I must have left out a ball bearing or something on the third time I had it apart. There's a ton of slop.
GONE-Monroe struts with under 20k on them.

This post has been edited by roostmeyer: Feb 1 2019, 06:31 PM
Go to the top of the page
 
+Quote Post
roostmeyer
post Aug 20 2018, 05:36 PM
Post #2


Advanced Member
**

Group: Advanced Members
Posts: 559
Joined: 20-January 09
From: Wichita, KS
Member No.: 3,727



Costa's was going to take the majority of this stuff off my hands, but hasn't been around to reply. If somebody has contact info for him please PM me. Otherwise all of this is probably back on the market.
Go to the top of the page
 
+Quote Post
Knight Industrie...
post Jan 23 2019, 03:03 AM
Post #3


newbie


Group: Advanced Members
Posts: 1
Joined: 23-January 19
From: Dallas Texas
Member No.: 223,998



Any of this still available :-) or should I ping Costa's :-)
Go to the top of the page
 
+Quote Post
GCrites80s
post Jan 26 2019, 02:47 AM
Post #4


Advanced Member
**

Group: Advanced Members
Posts: 664
Joined: 30-January 15
From: Columbus, OH
Member No.: 223,855



^You get these parts dialed in and you won't have to let off in the canyons even in Super Pursuit Mode
Go to the top of the page
 
+Quote Post
roostmeyer
post Feb 1 2019, 06:27 PM
Post #5


Advanced Member
**

Group: Advanced Members
Posts: 559
Joined: 20-January 09
From: Wichita, KS
Member No.: 3,727



Yep, he picked it up last year in the new family truckster.
Go to the top of the page
 
+Quote Post

Reply to this topicStart new topic
2 User(s) are reading this topic (2 Guests and 0 Anonymous Users)
0 Members:

 



Lo-Fi Version Time is now: 19th November 2024 - 10:17 PM