 splicing/soldering tech |
|
|||||||||
  |
 Jun 26 2008, 09:53 AM
Post
#1
|
|
|
Advanced Member  Group: Advanced Members Posts: 854 Joined: 26-December 03 From: NYC, NY Member No.: 50  |
I need to extend some wiring.
In the past ive used resin core solder and heat shrink tubing with electrical tape and wiring loom over it. Is this the correct way? Will it change readings from sensors like the TPS ignition coil because of the rosin core solder? |
 |
 
|
|
Jun 26 2008, 02:07 PM
Post
#2
|
|
|
FRRAX Owner/Admin Group: Admin Posts: 15,428 Joined: 13-February 04 From: Ohio Member No.: 196 |
A proper splice should add minimal resistance to the circuit. If it was a high current circuit it could be a different issue, but for a sensor circuit, a few extra feet of properly sized wire and a good solder connection should be of little consequence.
Kevin (ex avionics technician) |
|
|
|
|
Jun 26 2008, 03:29 PM
Post
#3
|
|
|
Seeking round tuits Group: Advanced Members Posts: 5,522 Joined: 24-December 03 From: Kentucky Member No.: 33 |
Dunno about the TPS cable, but if you encounter any sensor cables with two insulated wires twisted together as a pair (not actually connected together), be sure to continue the twist in your extension.
|
|
|
|
|
Jun 26 2008, 03:32 PM
Post
#4
|
|
|
Veteran Member Group: Advanced Members Posts: 3,323 Joined: 30-March 06 From: Detroit Suburbs Member No.: 1,144 |
How many wires do you have to extend? Soldering is a PIA. If you have a lot of wires to extend it would be worth it to buy some good quality crimp connectors and the proper crimping plyers. I have quite a bit of wire shortening to do so I bought the stuff and am just looking for the time and gumption to do it.
|
|
|
|
|
Jun 26 2008, 04:10 PM
Post
#5
|
|
|
Collo Rosso Group: Advanced Members Posts: 1,220 Joined: 3-August 05 From: San Antonio, TX Member No.: 839 |
I just extended some oxygen sensor wiring with no issues at all. Used rosin-core solder, heat shrink, and then tons of electrical tape to keep it all together. No side effects at all.
I've had no good luck with crimp connections, though I'm sure some are better than others. |
|
|
|
|
Jun 26 2008, 05:09 PM
Post
#6
|
|
|
Veteran Member Group: Advanced Members Posts: 3,323 Joined: 30-March 06 From: Detroit Suburbs Member No.: 1,144 |
QUOTE (BigEnos @ Jun 26 2008, 12:10 PM)  I've had no good luck with crimp connections, though I'm sure some are better than others. I would have agreed with you until I got the right plyers. That made all the difference. They have a point on one side that pinches in the middle. Hard to describe. I can't find a pic of what I have. |
|
|
|
|
Jun 26 2008, 05:56 PM
Post
#7
|
|
|
Collo Rosso Group: Advanced Members Posts: 1,220 Joined: 3-August 05 From: San Antonio, TX Member No.: 839 |
QUOTE (StanIROCZ @ Jun 26 2008, 11:09 AM) QUOTE (BigEnos @ Jun 26 2008, 12:10 PM) I've had no good luck with crimp connections, though I'm sure some are better than others. I would have agreed with you until I got the right plyers. That made all the difference. They have a point on one side that pinches in the middle. Hard to describe. I can't find a pic of what I have. For the little bit I need to splice wires, soldering works for me. Once it's done I never worry about it. |
|
|
|
|
Jun 26 2008, 07:16 PM
Post
#8
|
|
|
Advanced Member Group: Advanced Members Posts: 854 Joined: 26-December 03 From: NYC, NY Member No.: 50 |
QUOTE (StanIROCZ @ Jun 26 2008, 09:32 AM) How many wires do you have to extend? Soldering is a PIA. If you have a lot of wires to extend it would be worth it to buy some good quality crimp connectors and the proper crimping plyers. I have quite a bit of wire shortening to do so I bought the stuff and am just looking for the time and gumption to do it. Right now I only have a couple dozen wires to extend for the delteq. I've looked at those mil spec wire crimpers to build some cannon plug terminals and I can't justify the cost. I can see that it would be worth it if/when I decide to rewire everything. But for now it just doesn't seem worth it. Thanks for the input guys. |
|
|
|
|
Jun 26 2008, 09:06 PM
Post
#9
|
|
|
Advanced Member Group: Advanced Members Posts: 689 Joined: 8-May 06 From: Charlotte, NC Member No.: 1,201 |
I had few crimped wires work loose in the past. Now, if I haveto crimp, I also solder them into the connector.
|
|
|
|
|
Jun 28 2008, 04:33 PM
Post
#10
|
|
|
Engine and Tools Moderator Group: Advanced Members Posts: 1,859 Joined: 23-December 03 From: Lebanon TN Member No.: 6 |
QUOTE (StanIROCZ @ Jun 26 2008, 12:09 PM) I would have agreed with you until I got the right pliers. That made all the difference. They have a point on one side that pinches in the middle. Hard to describe. I can't find a pic of what I have. Here's one, kind of hard to see, the point is in the top die in the picture:
Attached File(s)
|
|
|
|
|
1 User(s) are reading this topic (1 Guests and 0 Anonymous Users)
0 Members:
| Lo-Fi Version | Time is now: 4th November 2024 - 02:20 AM |